Das Tuningkit für den Umarex HDR 68 CO2 Revolver
bringt eine enorme Leistungssteigerung
auf ca. 20 Joule mit CO2 - bzw. bis zu 30 Joule mit HP und erhöhtem Ausgangsdruck.
The tuning kit for the Umarex HDR68 CO2
revolver
brings an enormous increase in performance to >20 joules with CO2 - or 30 joules with HP and increased output pressure.
(bei den 11J modellen wird nur der
Ventilpin benötigt)
(only the valve pin is required for the 11J
models)
Es muss nur der Ventilpin ausgetauscht, Ventilkammerreduzierer (Alu- oder Plastikteil hinter dem Druckindikator) entfernt und mit Hilfe des mitgelieferten Montagewerkzeugs der Flow-Reducer ins Griffstück einsetzt werden. Für den Umbau ist es erforderlich den CO2 Revolver fast komplett zu zerlegen und wieder zusammenzubauen. Dies gelingt durch den relativ einfachen Aufbau und etwas Recherche.
All you have to do is replace the valve
pin, remove the valve chamber reducer (aluminum or plastic part behind the pressure indicator) and insert the flow reducer into the handle using the assembly tool supplied. For the conversion it
is necessary to dismantle the CO2 revolver almost completely and reassemble it. This is achieved through the relatively simple structure and research in the
Internet.
Der upgrade Flow-Reducer wird mit Hilfe des mitgelieferten Montagehilfe in seinen Sitz
gedrückt.
The upgrade flow reducer is pressed into its seat using the includet
assembly tool.
Der Rocketkey.68 Ventilpin ist etwas kürzer als das Original Teil und hat eine optimierte Spitzengeometrie was eine längere Ventilöffnungszeit bewirkt. Da der originale Ventilpin aus einem sehr
weichen Material besteht und vom Hersteller mit Schraubensicherungskleber eingeklebt wurde, muss der Bolt, vor dem Herausschrauben, im Bereich des Gewindes mit einem Jet Feuerzeug oder auf einer
elektrischen Heizplatte etwas erhitzt werden, um den Schraubenkleber zu lösen. So kann das Originalteil mit einem passenden Schlitzschraubendreher leicht herausgeschraubt werden.
The Rocketkey.68 valve pin is a little shorter than the
original part and has a different tip geometry which results in a longer valve opening time. Since the original valve pin is made of a very soft material and was glued in by the manufacturer with
screw locking adhesive, the screw must be heated a little in the area of the thread with a jet lighter or on an electric heating plate in order to loosen the screw adhesive. The original part can
easily be unscrewed with a suitable slotted screwdriver.
Der Rocketkey
Ventilpin und der Flow-Reducer bestehen aus hochfestem eloxiertem Aluminium (A7075) was eine einfache Montage und sichere Funktion garantiert.
The Rocketkey valve pin and the flow reducer are made of high-strength anodized
aluminum, which guarantees easy installation and reliable operation.
Durch die starke Leistungserhöhung nicht für Paintball geeignet!
Not suitable for paintball due to the strong increase in performance!
Der Erwerb und Besitz der Tuningteile ist erlaubt.
The purchase and possession of the tuning parts is
allowed.
Der Einbau ist in Deutschland verboten und führt zum Verlust von
Gewährleistungsansprüchen. Bitte respektieren Sie Ihre lokalen Gesetze!
Installation is prohibited in Germany and leads to the loss of warranty
claims. Please respect your local law!
Umarex hat uns gebeten folgenden Warnhinweis mit den Angeboten zu
verbreiten:
Umarex asked us to distribute the
following warning with the offers:
Lieferumfang:
what you get:
Rocketkey.68 MAX POWER Kit - bestehend aus upgrade Flow Reducer und Ventilpin - passend für den Umarex
HDR68 (7,5J "F"Modelle) - incl. Montagewerkzeug
Rocketkey.68 MAX POWER Kit - consisting of upgrade flow reducer and valve
pin - suitable for the Umarex HDR68 (7.5J "F" models) - including assembly tool - Only the valve PIN is required to increase the
performance of the 11J models.
+ kostenloses Muster / + free sample
39,95 €
inkl. MwSt, zzgl. Versandkosten
Versandkostenfrei in folgende Länder: Mehr anzeigen Weniger anzeigen
Das neue MAX Power Exportventil-Kit für den Umarex t4e HDR 50 CO2 Revolver in der 7,5 Joule Variante.
Rocketkey.50 the new MAX Power export valve kit for the Umarex t4e HDR 50 CO2
revolver in the 7.5 joule version.
Beste Qualität, Leistungssteigerung und Zuverlässigkeit mit weltweitem Schnell-Versand!
Best quality and reliability with worldwide fast shipping
Es muss nur der Ventilpin ausgetauscht, Ventilkammerreduzierer (Aluteil hinter dem Druckindikator) entfernt und mit Hilfe des mitgelieferten Montagewerkzeugs der Flow-Reducer ins Griffstück einsetzt werden. Für den Umbau ist es erforderlich den CO2 Revolver fast komplett zu zerlegen und wieder zusammenzubauen. Dies gelingt durch den relativ einfachen Aufbau und Recherche mit Internetvideos.
All you have to do is replace the valve
pin, remove the valve chamber reducer (aluminum part behind the pressure indicator) and insert the flow reducer into the handle using the assembly tool supplied. For the conversion it is
necessary to dismantle the CO2 revolver almost completely and reassemble it. This is achieved through the relatively simple structure and research with Internet
videos.
Der upgrade Flow-Reducer wird mit Hilfe des mitgelieferten Montagehilfe in seinen Sitz gedrückt.
The upgrade flow reducer is pressed into its seat using the includet assembly tool.
Der Rocketkey.50 Ventilpin ist etwas kürzer als das Original Teil und hat eine optimierte Spitzengeometrie was eine längere Ventilöffnungszeit bewirkt. Da der originale Ventilpin aus einem sehr
weichen Material besteht und vom Hersteller mit Schraubensicherungskleber eingeklebt wurde, muss der Bolt, vor dem Herausschrauben, im Bereich des Gewindes mit einem Jet Feuerzeug oder auf einer
elektrischen Heizplatte etwas erhitzt werden, um den Schraubenkleber zu lösen. So kann das Originalteil mit einem passenden Schlitzschraubendreher leicht herausgeschraubt werden.
The Rocketkey.50 valve pin is a little shorter than the
original part and has a different tip geometry which results in a longer valve opening time. Since the original valve pin is made of a very soft material and was glued in by the manufacturer with
screw locking adhesive, the screw must be heated a little in the area of the thread with a jet lighter or on an electric heating plate in order to loosen the screw adhesive. The original part can
easily be unscrewed with a suitable slotted screwdriver.
Der Rocketkey
Ventilpin und der Flow-Reducer bestehen aus hochfestem eloxiertem Aluminium (A7075) was eine einfache Montage und sichere Funktion garantiert.
The Rocketkey valve pin and the flow reducer are made of high-strength anodized
aluminum, which guarantees easy installation and reliable operation.
------------------------------------------------------------
Durch die starke Leistungserhöhung nicht für Paintball geeignet!
Not suitable for paintball due to the strong increase in performance!
Der Erwerb und Besitz der Tuningteile ist erlaubt.
The purchase and possession of the tuning
parts is allowed.
Der Einbau ist in Deutschland verboten und führt zum Verlust von Gewährleistungsansprüchen. Bitte respektieren Sie Ihre lokalen
Gesetze!
Installation is prohibited in
Germany and leads to the loss of warranty claims. Please respect your local law!
Umarex hat uns gebeten folgenden Warnhinweis mit den
Angeboten zu verbreiten:
Umarex asked us to distribute the
following warning with the offers:
------------------------------------------------------------
Lieferumfang:
what you get:
Rocketkey.50 MAX POWER Kit - bestehend aus upgrade Flow Reducer und Ventilpin - passend für den Umarex HDR50 (7,5J
"F"Modelle) - incl. Montagewerkzeug
Rocketkey.50 MAX POWER Kit - consisting of upgrade flow reducer and valve pin -
suitable for the Umarex HDR50 (7.5J "F" models) - including assembly tool - Only the valve PIN is required to increase the performance of the 11J models.
39,95 €
inkl. MwSt, zzgl. Versandkosten
Versandkostenfrei in folgende Länder: Mehr anzeigen Weniger anzeigen
Das neue MAX Power Exportventil-Kit für die Umarex t4e HDP 50 CO2 Pistole in der 7,5 Joule Variante.
Rocketkey.50 the new MAX Power export valve kit for the Umarex t4e HDP 50 CO2 pistol
in the 7.5 joule version.
Beste Qualität, Leistungssteigerung und Zuverlässigkeit mit weltweitem Schnell-Versand!
Best quality and reliability with worldwide fast shipping
All you have to do is replace the valve pin,
remove the valve chamber reducer (aluminum part behind the pressure indicator) and insert the flow reducer into the handle using the assembly tool supplied. For the conversion it is necessary to
dismantle the CO2 revolver almost completely and reassemble it. This is achieved through the relatively simple structure and research with Internet videos.
Der upgrade Flow-Reducer wird mit Hilfe des mitgelieferten Montagehilfe in seinen Sitz gedrückt.
The upgrade flow reducer is pressed into its seat using the includet assembly tool.
Der Rocketkey.50 Ventilpin ist etwas kürzer als das Original Teil und hat eine optimierte Spitzengeometrie was eine längere Ventilöffnungszeit bewirkt. Da der originale Ventilpin aus einem sehr
weichen Material besteht und vom Hersteller mit Schraubensicherungskleber eingeklebt wurde, muss der Bolt, vor dem Herausschrauben, im Bereich des Gewindes mit einem Jet Feuerzeug oder auf einer
elektrischen Heizplatte etwas erhitzt werden, um den Schraubenkleber zu lösen. So kann das Originalteil mit einem passenden Schlitzschraubendreher leicht herausgeschraubt werden.
The Rocketkey.50 valve pin is a little shorter than the
original part and has a different tip geometry which results in a longer valve opening time. Since the original valve pin is made of a very soft material and was glued in by the manufacturer with
screw locking adhesive, the screw must be heated a little in the area of the thread with a jet lighter or on an electric heating plate in order to loosen the screw adhesive. The original part can
easily be unscrewed with a suitable slotted screwdriver.
Der Rocketkey
Ventilpin und der Flow-Reducer bestehen aus hochfestem eloxiertem Aluminium (A7075) was eine einfache Montage und sichere Funktion garantiert.
The Rocketkey valve pin and the flow
reducer are made of high-strength anodized aluminum, which guarantees easy installation and reliable operation.
Durch die starke Leistungserhöhung nicht für Paintball
geeignet.
Not suitable for paintball due to the strong increase in
performance.
------------------------------------------------------------
Durch die starke Leistungserhöhung nicht für Paintball geeignet!
Not suitable for paintball due to the strong increase in performance!
Der Erwerb und Besitz der Tuningteile ist erlaubt.
The purchase and possession of the tuning
parts is allowed.
Der Einbau ist in Deutschland verboten und führt zum Verlust von Gewährleistungsansprüchen. Bitte respektieren Sie Ihre lokalen
Gesetze!
Installation is prohibited in
Germany and leads to the loss of warranty claims. Please respect your local law!
Umarex hat uns gebeten folgenden Warnhinweis mit den Angeboten
zu verbreiten:
Umarex asked us to distribute the
following warning with the offers:
------------------------------------------------------------
Lieferumfang:
what you get:
Rocketkey.50 MAX POWER Kit (20 Joule) - bestehend aus upgrade Flow Reducer und Ventilpin - passend für den Umarex
HDP50 (7,5J "F"Modelle) - incl. Montagewerkzeug
Rocketkey.50 MAX POWER Kit - consisting of upgrade flow reducer and valve pin -
suitable for the Umarex HDR50 (7.5J "F" models) - including assembly tool - Only the valve pin is required to increase the performance of the 11J models.
39,95 €
inkl. MwSt, zzgl. Versandkosten
Versandkostenfrei in folgende Länder: Mehr anzeigen Weniger anzeigen
Rocketkey.68 das original Full Power Exportventil-Kit für die Umarex T4E HDS 68 und HDX 68 CO2 Shotguns.
Beste Qualität, Leistungssteigerung und Zuverlässigkeit mit weltweitem Schnell-Versand!
Best quality, power upgrade and reliability with worldwide fast shipping
· >20 Joule Leistung durch tauschen von nur einem Teil und herausnehmen des Ventilreduzierers (schwarzes Kunststoffteil)
· harteloxiertes hochfestes Material für sicher Montage und ewige Haltbarkeit!
· beste Performance verbesserte Haltbarkeit und Dichtheit des Systems
HDX68 -HDS68...?
es ist im Prinzip bei beiden CO2 Shotguns genau das Gleiche umzubauen.
Volumenreduzierer (schwarzes Kunststofteil) aus der Ventilkammer entfernen und den Ventilpin gegen den original Rocketkey.68 Ventilpin austauschen. Der Ventilpin ist der gleiche. (Hauptunterschiede der Systeme sind lediglich, dass die HDX eine größere Ventilkammer und einen längeren Lauf hat.)
Die HDS kommt so auf ca. 20 - die HDX auf 40 Joule.
HDX68 -HDS68 ...?
In principle, it is exactly the same to convert both CO2 shotguns.
Remove the volume reducer (black plastic part) from the valve chamber and replace the valve pin with the original Rocketkey.68 valve pin. The valve pin is the same. (The main differences between the systems are that the HDX has a larger valve chamber and a longer barrel.)
The HDS comes to around 20 - the HDX to 40 joules.
Holt die maximale Leistung von über 40 Joule* aus den T4e HDX68- und 20 Joule aus der HDS68 CO2 Shotgun.
(*temperaturabhängig)
Gets the maximum output
of over 40 joules * from the T4e HDX68 and 20 Joules from HDS68 CO2 Shotgun. (* depending on temperature)
Der original Rocketkey.68 Tuning Kit bringt eine massive Leistungssteigerung beim HDS68 CO2 Shotgun von
Umarex.
The original Rocketkey.68 tuning
kit brings a massive increase in performance to the HDX- and HDS68 CO2 Shotgun from Umarex.
Es müssen nur der Ventilpin ausgetauscht und der Volumen-Reduzierer aus dem Ventilgehäuse entfernt
werden.
Only the valve pin has to be exchanged and the volume reducer removed from the valve housing.
Der Rocketkey.68 Ventilpin ist etwas kürzer als das Original Teil und hat eine andere Spitzengeometrie was eine längere Ventilöffnungszeit bewirkt. Da der originale Ventilpin aus einem sehr
weichen Material besteht und vom Hersteller mit Schraubensicherungskleber eingeklebt wurde, muss der Bolt, vor dem Herausschrauben, im Bereich des Gewindes mit einem Jet Feuerzeug oder auf einer
elektrischen Heizplatte etwas erhitzt werden, um den Schraubenkleber zu lösen. So kann das Originalteil mit einem passenden Schlitzschraubendreher leicht herausgeschraubt werden.
The Rocketkey.68 valve pin is a little
shorter than the original part and has a different tip geometry which results in a longer valve opening time. Since the original valve pin is made of a very soft material and was glued in by the
manufacturer with screw locking adhesive, the screw must be heated a little in the area of the thread with a jet lighter or on an electric heating plate in order to loosen the screw adhesive. The
original part can easily be unscrewed with a suitable slotted screwdriver.
Die im Rocketkey.68 Ventilpin besteht aus hochfestem harteloxiertem Aluminium was eine sichere Montage und ewige
Haltbarkeit garantiert. Das Herausnehmen des Reduzierers aus der Ventilkammer bewirkt ein viel größeres Volumen in der Ventilkammer. So steht pro Schuss wesentlich mehr CO2 zur
Verfügung.
The valve pin in the Rocketkey.68 is made of high-strength, hard-anodized aluminum, which guarantees safe installation and eternal durability. Removing the reducer from the valve chamber creates a much larger volume in the valve chamber. This means that significantly more CO2 is available per shot.
Durch die starke Leistungserhöhung nicht für Paintball geeignet.
Not suitable for paintball due to the strong increase in performance.
------------------------------------------------------------
Durch die starke Leistungserhöhung nicht für Paintball geeignet!
Not suitable for paintball due to the strong increase in performance!
Der Erwerb und Besitz der Tuningteile ist erlaubt.
The purchase and possession of the tuning
parts is allowed.
Der Einbau ist in Deutschland verboten und führt zum Verlust von Gewährleistungsansprüchen. Bitte respektieren Sie Ihre lokalen
Gesetze!
Installation is prohibited in
Germany and leads to the loss of warranty claims. Please respect your local law!
Umarex hat uns gebeten folgenden Warnhinweis mit den Angeboten
zu verbreiten:
Umarex asked us to distribute the
following warning with the offers:
-----------------------------------------------------------
24,95 €
inkl. MwSt, zzgl. Versandkosten
Versandkostenfrei in folgende Länder: Mehr anzeigen Weniger anzeigen
Kontakt:
Das beantworten von eMails kann, auf Grund der großen Nachfrage, derzeit etwas länger dauern.
Darum nutze bitte bei dringenden Anliegen und technischen Fragen das Telefon oder WhatsApp!
Answering e-mails can currently take a little longer due to the high demand.
So please use the phone or WhatsApp for urgent matters and technical questions!
Telefon 035205 689272
Mobil / WhatsApp: 0174 3910994
eMail: tech23-sws@web.de
Das könnte Ihnen auch gefallen
Woldwide delivery with absolutly no issues!
If you have any questions about shipping or customs, please feel free to contact us!
nur 4,90 € innerhalb Deutschlands
8,90 EU delivery
24,50 USA, Canada, Asia delivery
ab 100 € Versandkostenfrei bei D und EU Versand!